MacBook Battery Health: Check Cycle Count and Capacity
Short answer: open System Settings › Battery and click the Info (i) button next to Battery Health. macOS shows the battery’s condition (Normal or Service Recommended) and its maximum capacity compared with new. For the cycle count, hold Option, click the Apple menu, choose System Information and select Power. Apple silicon MacBooks are rated for 1,000 cycles.
Checked 14 October 2026 against Apple Support (cycle-count table re-checked 15 November 2026) and the macOS 27 Golden Gate user guide. Commands tested on macOS 27.0.1.
TL;DR
- Health: System Settings › Battery › Battery Health (i) shows Condition and Maximum Capacity.
- Cycle count: Option-click Apple menu › System Information › Hardware › Power, or
system_profiler SPPowerDataTypein Terminal. - Rated life: 1,000 cycles on every Apple silicon MacBook and the MacBook Neo, with up to 80% capacity left at that point.
- Slow the wear: Optimized Battery Charging, or a fixed Charge Limit (80% to 100%) on macOS Tahoe 26.4 or later with Apple silicon.
- Replace it when macOS says Service Recommended or the battery no longer gets you through the day, not because of a single number.
How do I check MacBook battery health?
Apple’s built-in reading is the one to trust, so start there:
- Choose Apple menu › System Settings.
- Click Battery in the sidebar. You may need to scroll down.
- Click the Info (i) button next to Battery Health.
- Read Battery Condition and Maximum Capacity.
Maximum Capacity is the battery’s capacity relative to when it was new. A brand-new Mac shows 100%, and it drifts down as the battery ages. Some Macs also show Manage battery longevity in the same sheet, which reduces peak capacity to lengthen the battery’s life. Whether you see it depends on the model.
On an older macOS without Battery Health in Settings, hold Option and click the battery icon in the menu bar. You’ll see a status such as Normal, Replace Soon, Replace Now or Service Battery.
What do “Normal” and “Service Recommended” mean?
| Condition | What Apple says it means | What to do |
|---|---|---|
| Normal | The battery is functioning normally | Nothing. Keep an eye on maximum capacity over time |
| Service Recommended | The battery’s ability to hold a charge is less than when it was new, or it isn’t functioning normally | You can keep using the Mac. Book a battery service with Apple or an Apple Authorized Service Provider when the shorter runtime bothers you |
Apple’s guidance on Service Recommended is calm on purpose: it’s a heads-up, not an emergency. A swollen battery, a case that no longer sits flat, or a trackpad that clicks oddly is different. Stop using the Mac and get it looked at.
How do I find my MacBook’s battery cycle count?
A charge cycle is using 100% of the battery’s capacity, not one trip to the charger. Draining from 100% to 50%, recharging, then draining another 50% counts as one cycle.
From Apple’s cycle count page:
- Hold Option and click the Apple menu, then choose System Information.
- Under Hardware, select Power.
- Read Cycle Count under Battery Information › Health Information. Condition and Maximum Capacity are listed next to it.
How many cycles is a MacBook battery rated for?
Apple publishes a maximum cycle count per model. It designs each battery to keep up to 80% of its original capacity at that count. Summarised from Apple’s table:
| Rated cycles | Models |
|---|---|
| 1,000 | Every Apple silicon MacBook Air and MacBook Pro (M1 through M6, including M5 Pro and M5 Max and the PROLED XDR models), the MacBook Neo, the 12-inch Retina MacBook (2015 to 2017), the 13-inch MacBook (Late 2009 and Mid 2010), Intel MacBook Pro models from 2009 onward and Intel MacBook Air models from Late 2010 onward |
| 500 | MacBook Pro (15-inch, Late 2008), MacBook Air (Mid 2009) |
| 300 | MacBook models from 2006 to Mid 2009, including the MacBook (13-inch Aluminum, Late 2008), the original MacBook Air and MacBook Air (Late 2008), and MacBook Pro models up to Early 2008 plus the 17-inch Late 2008 |
MacBook Pro and MacBook Air cycle count limits by model
Find your model and year in Apple menu › About This Mac, for example “MacBook Pro (14-inch, 2023)”. Model names below are Apple’s own, from its cycle count table as published on 5 November 2026.
| Model | Years | Maximum cycle count |
|---|---|---|
| MacBook Pro with Apple silicon: 13-inch M1 and M2; 14-inch and 16-inch from 2021, 2023, Nov 2023 and 2024; 14-inch M5; M5 Pro or M5 Max, including PROLED XDR; 14-inch M6 | 2020 to 2026 | 1,000 |
| MacBook Pro (13-inch and 15-inch, 2016 to 2019; 16-inch, 2019; 13-inch, 2020), Intel with Thunderbolt 3 | 2016 to 2020 | 1,000 |
| MacBook Pro with Retina display (Retina, 13-inch and 15-inch) | Mid 2012 to Mid 2015 | 1,000 |
| MacBook Pro (13-inch, 15-inch and 17-inch) without Retina | 2009 to Mid 2012 | 1,000 |
| MacBook Pro (15-inch, Late 2008) | Late 2008 | 500 |
| MacBook Pro (15-inch and 17-inch) up to Early 2008, and MacBook Pro (17-inch, Late 2008) | 2006 to 2008 | 300 |
| MacBook Air with Apple silicon: M1, M2, M3, M4 and M5, 13-inch and 15-inch | 2020 to 2026 | 1,000 |
| MacBook Air (Retina, 13-inch) | 2018 to 2020 | 1,000 |
| MacBook Air (11-inch and 13-inch) | Late 2010 to 2017 | 1,000 |
| MacBook Air (Mid 2009) | Mid 2009 | 500 |
| MacBook Air (original) and MacBook Air (Late 2008) | 2008 | 300 |
| MacBook Neo | 2026 | 1,000 |
| MacBook (Retina, 12-inch) | Early 2015 to 2017 | 1,000 |
| MacBook (13-inch, Late 2009 and Mid 2010) | 2009 to 2010 | 1,000 |
| MacBook (13-inch Aluminum, Late 2008) and the other MacBook models from 2006 to Mid 2009 | 2006 to 2009 | 300 |
“MacBook Pro Retina” is the 2012 to 2015 line, so a Retina MacBook Pro’s limit is 1,000 cycles, and every MacBook Air sold since Late 2010 has the same 1,000-cycle rating.
Hitting the number doesn’t switch the battery off. A Mac at 1,050 cycles with 82% capacity and a Normal condition is fine to keep using. The count is a design target, and the condition tells you whether the battery is still behaving.
How do I check battery health in Terminal?
Both commands below are read-only. They don’t change any setting.
The same figures as System Information:
system_profiler SPPowerDataType | grep -E "Cycle Count|Condition|Maximum Capacity"
On macOS 27 this prints three lines, for example Cycle Count: 129, Condition: Normal and Maximum Capacity: 97%.
The raw battery registry, including Apple’s rated cycle count:
ioreg -rn AppleSmartBattery | grep -o -E '"(CycleCount|DesignCycleCount9C|DesignCapacity|NominalChargeCapacity)" ?= ?[0-9]+' | sort -u
CycleCountis your current cycle count.DesignCycleCount9Cis the rated count for your battery (1,000 on Apple silicon).DesignCapacityandNominalChargeCapacityare in mAh. Dividing the second by the first gives a rough health percentage.
That last figure won’t always match System Settings exactly. On our test MacBook it worked out to 96.6% (8,286 of 8,579 mAh) while macOS showed 97%. Apple says third-party readings may not be accurate and to rely on what macOS reports, so use the raw numbers for curiosity and scripts, and System Settings for decisions.
Charge right now:
pmset -g batt
This shows the current percentage, whether it’s charging, and the time remaining.
How do I slow down battery wear?
Lithium-ion batteries age fastest when they sit full and warm. macOS has two settings for that, both under System Settings › Battery, then the Info (i) button next to Charging:
| Setting | What it does | Needs |
|---|---|---|
| Optimized Battery Charging | Learns your routine and delays charging past 80% when you’re likely to stay plugged in for a long time, then finishes charging before you usually unplug | macOS Big Sur 11 or later |
| Charge Limit | A fixed ceiling you pick, from 80% to 100%. The battery menu then reads “Charged to [%] Limit” | macOS Tahoe 26.4 or later and a Mac with Apple silicon |
A few details from Apple’s battery health management page:
- When Optimized Battery Charging is delaying the charge, the battery menu shows Charging On Hold.
- Need a full battery for a flight? Click the battery icon in the menu bar and choose Charge to Full Now. It overrides either setting for that charge.
- With either setting on, your Mac still charges to 100% now and then to keep its charge estimates accurate. That’s expected.
Which should you use? If your MacBook lives on a desk dock, set a Charge Limit of 80% or 85%. If you unplug on a regular schedule, Optimized Battery Charging alone is usually enough.
Heat matters too. Don’t leave a MacBook charging under a pillow, on a bed or in a hot car. If the Mac runs hot and drains fast at the same time, something is working in the background; our guide to why a Mac battery drains fast walks through finding it.
When should you replace a MacBook battery?
Replace it when one of these is true:
- macOS shows Service Recommended and the shorter runtime gets in your way.
- The battery no longer lasts the stretch you need away from a charger.
- The Mac shuts down unexpectedly at a reported charge above zero.
- The case bulges, the trackpad stops clicking properly or the lid doesn’t close flat (stop using it and get it serviced).
Don’t replace it just because the cycle count passed 1,000 or maximum capacity dipped under 90%. Plenty of MacBooks run for years past that.
How do you keep an eye on battery health from the menu bar?
System Settings answers the question when you ask it. A menu bar monitor answers it before you think to ask. We make FavTray, so weigh our take accordingly.
| Tool | Shows | Alerts | Price |
|---|---|---|---|
| System Settings › Battery | Condition, maximum capacity, 24-hour battery level, 10-day energy use | No | Built in |
| System Information › Power | Cycle count, condition, maximum capacity | No | Built in |
| coconutBattery | Mac battery details, history, iPhone and iPad batteries | Plus | Free; Plus is a one-time purchase |
| FavTray System | Condition, maximum capacity, cycles, charging on hold, Low Power Mode, watts, today’s battery sessions | Pro | Free glance; Pro adds alerts |
FavTray’s System section keeps the battery next to CPU, memory, GPU and thermal state in one menu bar app. On the free tier you get battery condition, maximum capacity and cycles, system and charger watts, whether charging is on hold, Low Power Mode, what’s keeping the Mac awake, and today’s battery sessions. Pro adds battery health alerts with thresholds you set, alerts when the charger can’t keep up or an app keeps the Mac awake on battery, 7-day and 30-day history for battery percentage and watts, and 30 days of battery sessions. It’s read-only and runs locally, with no account.
coconutBattery is the better pick if battery history is all you want, or if you also want to check an iPhone or iPad battery from your Mac. The current version, 4.4, needs macOS 12 Monterey or later.
For a wider look at menu bar monitors, see iStat Menus vs Stats vs FavTray. Bluetooth accessories have their own batteries too: here’s how to check AirPods and Magic Keyboard battery on a Mac.
The quick checklist
- System Settings › Battery › Battery Health (i): condition and maximum capacity.
- System Information › Power: cycle count.
- Compare with 1,000 cycles if your MacBook has Apple silicon.
- Turn on Optimized Battery Charging, or set a Charge Limit if the Mac is usually plugged in.
- Service it when macOS says Service Recommended and the runtime no longer works for you.
FavTray is free to download, with a 7-day full Pro trial and no card. Pro is $4.99 once for one Mac; see pricing.
Sources (checked 14 October 2026): Determine battery cycle count for Mac laptops, If you see battery “Service Recommended”, About battery health management in Mac laptops, Change Battery settings on a Mac laptop, Check the condition of your battery.
Frequently Asked Questions
How do I check my MacBook battery health?
Choose Apple menu › System Settings, click Battery in the sidebar, then click the Info button next to Battery Health. You'll see the battery's condition (Normal or Service Recommended) and its maximum capacity, which is how much charge it can hold compared with when it was new. On older macOS versions, Option-click the battery icon in the menu bar.
What is a good battery cycle count for a MacBook?
Every Apple silicon MacBook Air, MacBook Pro and MacBook Neo is rated for 1,000 cycles, and so are Intel MacBook Pro models from 2009 and MacBook Air models from Late 2010 onward. Apple designs the battery to keep up to 80% of its original capacity at that count. A cycle is 100% of the battery's capacity used, so two half-discharges add up to one cycle.
What is the battery cycle count limit for a MacBook Pro with Retina display?
1,000 cycles. Apple rates every MacBook Pro with Retina display, the 13-inch and 15-inch models from Mid 2012 to Mid 2015, for a maximum of 1,000 cycles, the same as every MacBook Pro since 2009, including the 2016 to 2020 Intel models and all Apple silicon models. The battery is designed to keep up to 80% of its original capacity at that count.
What is the battery cycle count limit for a MacBook Air?
1,000 cycles for every MacBook Air from Late 2010 onward: the 11-inch and 13-inch models to 2017, the Retina models from 2018 to 2020, and every Apple silicon model from the M1 to the M5. The MacBook Air (Mid 2009) is rated for 500 cycles, and the original MacBook Air and the Late 2008 model for 300.
Is 85% battery health bad on a MacBook?
No. Apple designs MacBook batteries to keep up to 80% of their original capacity at their rated cycle count, so 85% is normal wear for an older Mac. What matters more is the condition in Battery settings. If it says Normal and the battery still lasts long enough for your day, there's no reason to replace it yet.
Should I limit my MacBook charge to 80%?
It can slow battery aging if your Mac sits on the charger most of the day. On macOS Tahoe 26.4 or later with Apple silicon, go to System Settings › Battery, click the Info button next to Charging and pick a Charge Limit between 80% and 100%. Optimized Battery Charging does something similar automatically by learning your routine.
Are third-party battery health apps accurate?
Apple recommends relying on the battery health macOS reports, because third-party apps may calculate it differently. A health figure worked out from the raw capacity numbers in the battery registry can differ from Apple's by a point or two. Use them for history and alerts, and treat System Settings as the reference.